Hub centric rings 72.6 - 60.1 mm
Hub centric ring 72,6-60,1 mm — also known as: hub rings, centering rings, wheel hub rings or spigot rings — fills the 6,2 mm gap between the wheel center bore and the vehicle hub. Without a hub centric ring, the wheel does not sit precisely on the hub, which can cause vibration at driving speed.
72.6 mm outer diameter is common in aftermarket wheels and also in some BMW OEM wheels. 60.1 mm inner diameter is common for several BYD, Dacia, Ford, Lexus, MG, Nissan, Renault, Suzuki, Toyota and Volkswagen models. This hub centric ring size (also written as 72,6-60,1) is typically used when installing an aftermarket wheel on a BYD or Dacia vehicle.
Hub centric rings are made of temperature-resistant and dimensionally precise engineering plastic. Height 10 mm, lip ~3 mm holds the ring in place during installation.
🚗 Compatible cars (hub size 60.1 mm)
The following cars have a hub size of 60.1 mm. This hub centric ring fits when the wheel center bore is 72.6 mm.
BYD
- Atto 3 Atto 3 (2022–)
Dacia
- Jogger Jogger (2022–)
- Sandero II (2012–2020), III (2020–)
- Spring Spring (2021–)
Ford
- Ka Ka+ (2016–2021)
Lexus
- IS XE10 (1999–2005), XE20 (2005–2013), XE30 (2013–)
- NX AZ10 (2014–2021), AZ20 (2021–)
- RX AL10 (2008–2015), AL20 (2015–2022), AL30 (2022–)
- UX UX (2018–)
MG
- ZS EV ZS EV (2019–)
Nissan
- Micra K13 (2010–2017), K14 (2017–)
Renault
- Captur I (2013–2019), II (2019–)
- Clio III (2005–2012), IV (2012–2019), V (2019–)
- Megane III (2008–2015), IV (2015–2023)
- Megane E-Tech Megane E-Tech (2022–)
- Zoe Zoe (2012–2024)
Suzuki
- S-Cross S-Cross (2013–)
- Vitara LY (2015–)
Toyota
- Auris E150 (2006–2012), E180 (2012–2018)
- Avensis T220 (1997–2003), T250 (2003–2009), T270 (2009–2018)
- bZ4X bZ4X (2022–)
- C-HR AX10 (2016–2023)
- Camry XV70 (2017–)
- Carina Carina E T190 (1992–1997)
- Corolla E210 (2018–)
- RAV4 XA20 (2000–2005), XA30 (2005–2012), XA40 (2012–2018), XA50 (2018–)
- Supra A60 (1981–1986), A70 (1986–1993), A80 (1993–2002)
Volkswagen
- Kupla / Beetle (klassikko) Beetle / Kupla (1938–2003)
🔧 Installation guide
Clean the car hub and wheel center bore from dirt and rust. A dry, clean surface ensures a tight fit.
Press the hub centric ring onto the car hub. It should fit snugly — not too loose and not forced.
Lift the wheel into place. The wheel center bore sits on top of the hub centric ring, centering the wheel precisely on the hub.
Tighten the wheel bolts/nuts in a cross pattern to the correct torque. The hub centric ring stays between the wheel and hub.
Measure your wheel center bore diameter (72.6 mm) and your car hub diameter (60.1 mm). See measuring guide →
Affordable letter delivery. In-stock products ship within 24h of order.
Contact us: info@hubcentric-rings.com. We help you find the right size!